Painting a Popup Tent Camping Trailer

As I decided to rebuild my pop-up tent trailer for family camping, I thought I should go ahead and paint it as well. I did not want to take it to Maaco or have a professional paint it because I did not want to spend that kind of money. I figured I could do this all myself for a whole lot cheaper. Here is what I did.

First I removed all the canvas off the tent trailer. Since a tent trailer is designed to have the canvas removed, this was a rather simple task. You will also need to decide if you are going to paint the inside of the trailer too. In my case, I did – in fact I tore out the inside completely cause I was planning on doing a complete restore. 

Canvas removal and body preparation

Outside: In order for the paint to look nice and adhere well, you need to remove all the decals, pin-striping etc. After all the decals are removed, you should give the outside a nice light sanding with about 120 grit sandpaper. 

After sanding, give the trailer a nice power wash. This will get all the loose dirt and sandpaper residue (for the original paint & sanding) off. 

Now it is time to mask off the areas of the trailer you don’t want to get painted. I masked off:

• Tires
• Door handle / latch
• Side lights
• Rear lights
• Trailer Tongue

For the parts I didn’t mask off AND didn’t want painted, I removed. for example, I removed the outside freshwater supply inlet and the land line power inlet.

Freshwater Supply Inlet

The Tongue on my Trailer was rusted and a very brownish color – I used this spray I got from Wal-mart that turns rust into black primer. Came out looking real nice.

Ok- now before you go any further, you will need a few items for the painting. Here is what you will need:

•  an HVLP Paint sprayer (I purchased this at Harbor Freight on sale for $17)
• An air compressor (the bigger the better as far as gallons go – but at least a 2 gallon)
• Vaseline
• 1 to 2 Gallons of Oil Based Paint for painting steel (I used BAR-OX Gloss enamel white paint. It is made by Devoe Paint and I purchased it from Neumann Paint and Supply 928-472-9054)
• Paint Thinner

Now it is time to paint. First, make sure you are out in the open so the paint fumes and over spray don’t get on anything you care about. Now start your air compressor going to fill up the air tank. To get the paint ready, fill your HVLP sprayer about 3/4 of the way with the Paint. Now add paint thinner in small doses to make the paint more like water in thickness. This is so you don’t clog up your sprayer. Attach your Paint Hopper to the HVLP sprayer and then attach the sprayer to the Air hose.

IMPORTANT NOTE:  Take that Vaseline that I told you to have handy and smear it on all parts of your body that is exposed to the air – Face, hands, ears, neck etc. WHY? Because you are going to get overspray and oil based paint doesn’t come off very easily. Having Vaseline on your skin allows you to just wipe off all the over spray that gets on your body. It is like wearing a paint suit, only cheaper

To spray, start at one end of the trailer and spray about 12 inches away from the surface of the trailer. Continue horizontally about your arms reach. Then let go of the sprayer trigger. And repeat this process back to where you started from. You want even spray stokes back and forth. Do this a total of two times before moving lower on the body. Then move to the area you haven’t painted on that side of the trailer and repeat this process over and over until the whole trailer is painted.

Painted popup trailer

When you are done painting, let it dry for at least 24 hours – then use a buffer and buff your new paint job

I am in the process of writing a series of step by step articles (with pictures!) about my restoration process. If you would like to be notified about that series then subscribe to my blog in the yellow box below.

Did you enjoy this article? Please subscribe to RVHobby to receive all the FREE updates!

Tagged as: camping, popup, rebuild, restore, tent trailer